|
|
Post by tarzan on Sept 20, 2016 16:10:52 GMT
Hi, i've just began with some basic adaptations and i need some suggestions..
-can i disable only seatbelts alarm leaving the dash red bulb working?
-i can't change the fis theme ! it still remains the default one even i try the other 3 settings..
My car is 10/2014 highline Mib1 with colour fis and Discover Media nav..
obd11 seems perfectly working with other adaptions but this carbon look doesnt work.
can you help me?
thanks!
|
|
|
|
Post by Daniel (Germany) on Sept 20, 2016 19:15:47 GMT
May its not possible to code it in every golf 7. I know it is not possible in evry seat leon 5f i dont know why but may the same at golf
|
|
|
|
Post by tarzan on Sept 20, 2016 20:54:48 GMT
Oh no...i hope that someone will find soon a workaround:(
I noticed that a lot of tweaks can be obtained in different ways...from adaption,manual coding..a big business!
probably my model shoud be hacked differently than usual..
|
|
|
|
Post by axlesofevil on Sept 21, 2016 8:53:41 GMT
Guys, I have an early morning issue happening. I could not get my fog lights to work on high beam. I came across a post that detailed Byte 14, bit 3 to enable this. I went into long coding and the first three bits were enabled (1,2 & 3). So I thought instead of just exiting, I would press the gree check button, and it told me "coding accepted" Here is the before and after setting 09 Central Electrics Date: 2016-09-21 02:55 Mileage: 3622 km Long coding: Old value: 00111A464041A2F969E44000001407201800000000000000000000000000 New value: 00111A464041A2F969E44000001407201800000000000000000000000000 As can be seen, the OLD value is the same as the NEW value, but now after doing this I have the yellow triangel, and a message that pops up saying 09 central electrics incorrect coding, and it throws a fault: Lighting failure on the info screen on the dash. I have tried clearing the codes, and resetting the infotainment but this error remains. Any ideas please?  UPDATED: PLEASE SEE NEXT POST BELOW (otherwise known as operator error).... |
|
|
|
Post by axlesofevil on Sept 21, 2016 9:25:08 GMT
OPPSSS!!!! MY BAD (and stupidity!)
Refering to my previous post, the lighting error had nothing to do with the coding above. I had just completed a Euro LED tail light install with rear fog light option enabled, and in the adaptation, I chose the LED Lamp option. That was last night, I quickly tested it, it worked, and I went inside and thought nothing else of it. I was making some changes this morning and "noticed" the problem as stated in my previous post.
Turns out that if you are going to retrofit your rear tails with the OEM LED lights (which are awesome BTW), and want the rear fog light option, choose option 9, which is the one for the Guhllampe 27W: H15, and not the LED option.
I did not delete this post because someone else could benefit in case you find yourself in a similar situation.
Happy messing!
Mark
|
|
|
|
Post by tarzan on Sept 22, 2016 13:17:04 GMT
well... i've find a lot of stuff here  this pdf is awesome even if Spanish ! So we have another language to translate if you follow the pdf creators site you will discover a lot more stuff and pdfs... about lights, lane and tyre sensors .... good reading! goo.gl/D37qgp |
|
|
|
Post by mathmk7 on Sept 25, 2016 14:23:56 GMT
Hello , Id like to know if the coding process for (dynamic breaks ) is the one to enable the emergency flashing brakes lights when hard braking ?
I don't know how to acces the channel in adaptation mod !! Is channel =bytes and value=bit ?
anyone can help me ?
Only thing I found is THIS
Select control unit( brakes)
Adaptation
Channel 9
Value 2
|
|
|
|
Post by dv52 (Australia) on Oct 13, 2016 1:09:43 GMT
Hello , Id like to know if the coding process for (dynamic breaks ) is the one to enable the emergency flashing brakes lights when hard braking ? I don't know how to acces the channel in adaptation mod !! Is channel =bytes and value=bit ? anyone can help me ? Only thing I found is THIS Select control unit( brakes) Adaptation Channel 9 Value 2 mathmk7: Hello. Not sure where you got your instructions, but they are not suitable for a mk7! I have no idea whether this will work and my suggestion is totally untested, but you might want to try the following: - Select Central Electrics
- Select Security Access
- Enter magic number 31347
- Select Adaptation
- Search for Assistance light functions
- Select Notbremsanzeige NBA (which means in English) emergency brake announcementNBA
- change value to active
- exit software
- Drive at reasonable speed with someone driving behind the car
- When safe to do so, brake hard and see whether the brake lights flash
As I said, this is just a guess, but the RoW vehicles in my database have this channel setting as "active" whereas the NAR models have a factory setting of "not active"
Don
|
|
|
|
Post by mryflyguy on Oct 17, 2016 20:30:40 GMT
I think this means the LEDs will stay lit while the turn signal is on, right? Is there a video of this Adaptstion somewhere?
Avoid Dimming LED Lights when Blinking
Select Control unit 09 (Central Electrics)
Security access
Access Code 31347
Adaptation
(12)-Leuchte2SL VLB10-Lichtfunction E2
Select: not active
(12)-Leuchte3SL VRB21-Lichtfunction E3
Select: not active
|
|
|
|
Post by shadptr on Oct 20, 2016 22:08:58 GMT
Hi. Could someone assist in translating step by step with the last item in the rain sensing mod please?
Rain Closing
Select Control unit 09 (Central Electrics)
Security access
Access code 31347
Adaptation
(15) Access Control 2-Regenschliessen_ein_aus
Value: Permanent
(16) Access Control 2-Regenschliessen_art
Value: Permanent
(28) Zugriffskontrolle 2-Menuesteuerung Regenschliessen
Value:Aktif
Select Control unit 09 (Central Electrics)
Control unit Long Coding
Subsystem: Rain / Light Sensor (RLS)
Byte 0
Bit 1-Bit 2 DeActivate
Specifically the codinf byte 0 of rain ligh sensor light system.
I went into coding. Found regen licht sensor. Clicked it and it offered options. Not sure what to select. Then i click the 0-1 on top right to see the bytes. It says to untick bit 1 and 2 of byte 0. I dont think im in the right area because it is not ticked. Please help. 😆
|
|
|
|
Post by dv52 (Australia) on Oct 21, 2016 0:39:49 GMT
Hi. Could someone assist in translating step by step with the last item in the rain sensing mod please? Rain Closing Select Control unit 09 (Central Electrics) Security access Access code 31347 Adaptation (15) Access Control 2-Regenschliessen_ein_aus Value: Permanent (16) Access Control 2-Regenschliessen_art Value: Permanent (28) Zugriffskontrolle 2-Menuesteuerung Regenschliessen Value:Aktif Select Control unit 09 (Central Electrics) Control unit Long Coding Subsystem: Rain / Light Sensor (RLS) Byte 0 Bit 1-Bit 2 DeActivate Specifically the codinf byte 0 of rain ligh sensor light system. I went into coding. Found regen licht sensor. Clicked it and it offered options. Not sure what to select. Then i click the 0-1 on top right to see the bytes. It says to untick bit 1 and 2 of byte 0. I dont think im in the right area because it is not ticked. Please help. 😆 shadptr : Hello. First, I assume that you have read the countelss posts on various forums where folk that have tried this tweak have reported that it doesn't work. That said, some have succeeded in getting this function to operate - I hope that you are in this latter category!!
OK - now to your question - where did you get those instructions??? Here is a copy of the long coding helper screen from VCDS that shows what the Bits actually do:
As you can see, for this tweak, you need to ENABLE the two bits - not "Deactivate" them as per your instructions. I have read in a few posts where some have gotten this function to work by only enabling Bit 2, but as I said, this is a particularly temperamental tweak and the original instructions did have both Bits enabled.
Good luck - and don't be too disappointed if you can't get the tweak to work!!!!
Don
|
|
|
|
Post by shadptr on Oct 21, 2016 10:08:14 GMT
Ah. Tyvm for your response Don. I actually got my steps from the first page of this thread.
Will try tonight.
|
|
|
|
Post by Eugene on Nov 15, 2016 23:18:16 GMT
Looking for the adaptation to enable SOC display - vcds tweak simple says change the "battery display" adaptation, but I can't fund such in the obdII app...
|
|
|
|
Post by Valtteri on Dec 11, 2016 22:30:03 GMT
Hello, i just got my OBD11 and i can't figure out how i can change Drive Profile. I don't have that button in dashboard because i thought that i could change driving profile with OBD11. I activated Drive Profile but can't find how to change the actual profile.
So is it possible to change this with obd11? or do i need to buy all the accessories needed?
Drive Profile on ODB
Select Control unit 19
Control unit long coding
Byte 08
Bit 4 Activate
|
|
|
|
Post by TTK on Dec 13, 2016 13:34:22 GMT
As tu tout simplement cette option ?
A priori, non !
|
|
|
|
Post by Joeblownewjersey on Dec 21, 2016 4:32:05 GMT
|
|
|
|
Post by nicvail on Dec 29, 2016 18:35:45 GMT
I can't activate the "Window close when ignition off". I do not have the "(13) -Zugangskontrolle 2 released trailing FH cancel at Tueroeffnen
Value=Aktif" seting.
Can someone help me?
Nic
|
|
|
|
Post by mathmk7 on Dec 29, 2016 20:58:21 GMT
If your car dont have automatic headlights then dont use the auto fonction ! |
|
|
|
Post by xagico on Dec 29, 2016 22:03:03 GMT
|
|
sheki
New Member
Posts: 1 
|
Post by sheki on Jan 1, 2017 16:30:16 GMT
Hallo leute wollte micht informieren wie ich die blinker von meinem Golf 7 R Variant auf dynamisches Blinken mit obdeleven programieren kann. danke für eure hilfe
|
|
|
|
Post by Daniel (Germany) on Jan 1, 2017 20:00:18 GMT
Gar nicht. Da alle verbauten led der blinker als eine leuchte hinterlegt sind. Bei youtube gibts jemanden der hat das für hinten gemacht, aber das ist eine hardware sache und keine codierung
|
|
|
|
Post by Alltrack QC on Jan 6, 2017 2:14:15 GMT
Little problem here, trying to change the XDS setting on my Alltrack (wich is equip) after coding I accept the mod but the software asking the code (usually 31347)...Always getting an error wrong code?!
Any new code for the MY17?
|
|
|
|
Post by dv52 (Australia) on Jan 6, 2017 2:36:06 GMT
Little problem here, trying to change the XDS setting on my Alltrack (wich is equip) after coding I accept the mod but the software asking the code (usually 31347)...Always getting an error wrong code?! Any new code for the MY17? Alltrack QC: Not sure if you are aware, but VW's control modules get cranky if you try an incorrect security code. They generally "spit-the-dummy" and they show their disgust by locking-out for a period of time (about ten minutes, sometimes less). The lock-out time is measured with the ignition turned-on The magic number 31347 doesn't work on the Brakes module - try 20103. If this is not successful wait a while (lock-out time) with the ignition turned-on and then try 40168
Don
|
|
|
|
Post by AlltrackQC on Jan 8, 2017 12:14:05 GMT
Little problem here, trying to change the XDS setting on my Alltrack (wich is equip) after coding I accept the mod but the software asking the code (usually 31347)...Always getting an error wrong code?! Any new code for the MY17? Alltrack QC: Not sure if you are aware, but VW's control modules get cranky if you try an incorrect security code. They generally "spit-the-dummy" and they show their disgust by locking-out for a period of time (about ten minutes, sometimes less). The lock-out time is measured with the ignition turned-on The magic number 31347 doesn't work on the Brakes module - try 20103. If this is not successful wait a while (lock-out time) with the ignition turned-on and then try 40168
Don
The code 20103 Works perfectly un the brake module! Thanks Don |
|
|
|
Post by Wald on Jan 11, 2017 12:37:25 GMT
I have some problems with coding: 1. I tried to do this: "XDS Adjustment
Select Control unit 03 (ABS)
Adaptation
Select: Expanded Electronic Differential Lock
Options: Weak-Normal-Hard"But computer wants the access code 2. Comin Home/Leaving Home with Fog and LED
Select Control unit 09 (Central Electrics)
Security access
Access Code 31347
Adaptation
(4) Comfort lighting Coming Home Lights
Value :Nebellicht(Low Beam)
I have the menu on screen but lights don't work, i have no fog lights and DRL ae no LED but in lowe beam 3. Lap Timer Aktivation
Select Control unit 17 (Dashboard)
Control unit Long Coding
Byte 1
Bit 3 Activate
Coding was good but I don't see these function in the car, where is it, how to start laptimer? |
|
|
|
Post by dv52 (Australia) on Jan 12, 2017 0:40:31 GMT
Wald: In order of questions asked:
1 - look at the previous post by AlltrackQC
2. - Here is the adaptation-set for CH function
Check that the adaptation channel settings in the boxed-set in the picture are as shown.
3. The lap timer requires a particular firmware capability in the Dashboard module- I suspect that your car doesn't have this capability (alas)
Don |
|
|
|
Post by MrSlider on Jan 15, 2017 18:37:14 GMT
I'm looking for the cod for front (bixenon)and rear light that makes It "sparking" at high Speed Like Ferrari or lambo!!!
|
|
|
|
Post by golfmk7 on Jan 22, 2017 15:38:24 GMT
Hi you guys.
I was wondering if there is any code for disable the warning light on the dash saying: Danger of icy roads?
It is getting really annoying.
Looking forward to hearing from you.
- Best regards Mark - 2014 Golf mk7
|
|
|
|
Post by dv52 (Australia) on Jan 23, 2017 0:35:46 GMT
Hi you guys. I was wondering if there is any code for disable the warning light on the dash saying: Danger of icy roads? It is getting really annoying. Looking forward to hearing from you. - Best regards Mark - 2014 Golf mk7 golfmk7:
I'm not aware of a procedure to disable the Road Ice facility entirely, but you can alter the temperature(s) for the alarm/warning-message.
But first you need to understand the concept of Hysteresis , which is an engineering term. Hysteresis is a function that is embedded in a "closed-loop" system that differentiates between the switch-on and switch-off thresholds. In the Road Ice facility on a mk7, hysteresis is used to minimise driver annoyance in that there are two temperatures used: the lower temperature in the Road Ice facility is the temperature at which the warning message and alarm inititates - the higher temperature is the temperature at which the warning message clears. Without hysteresis, the driver would be continuously bombarded with alarms as the ambient temperature changes by a fraction of a degree around the threshold!
So here's how to change the Road Ice temperatures:
- Select Dashboard module @ address hex17
- Select Security access
- Enter the magic number 20103 - Note: this security code will only work for pre MY16 vehicles for this tweak
- Select Adaptation
- Follow the screenshot below
Don
PS: The 2 x adaptation channels shown in the picture above have a maximum limit. Entries over 10 degrees Celsius won't be accepted PPS: It is strongly suggested that a differential of at least 2 degrees Celsius (as per the factory settings) be allowed to avoid repeated alarms/warning messages - read explanation of Hysteresis above
|
|
|
|
Post by STANDARD H on Jan 24, 2017 7:26:05 GMT
Got my Rear LED Tail Lights from BEC which did not come with OBDeleven instructions. Can someone help me out? I'd like the turn signals to be the amber bulbs instead of the outer red lights, and currently, when I have the lights on (not DRL), all bulbs are lit, including the amber and the outer red lights act as the turn signal.
So, I need to program it where the ambers are off unless a turn signal is on, in other words. Thank you!
|
|
