|
Post by Thirsty on May 5, 2020 13:17:58 GMT
Use the following format to report bugsDescription of bug: your bug descriptionAndroid software version: your android version Phone: your android phone modelDongle variant: Firstgen or Nextgen Car: your vehicle brand, model and year App profile: your app user email or username Changelog
v0.21.3 - Fixed crash when trying to create vehicle manual
v0.21.2 - Fixed issue on Android 4.4 not able to open app
v0.21.1 - Fixed crash when opening Control Units in landscape
v0.21.0 - Fixed to force emails to lowercase while registering users - Fixed Basic Settings status change history - Fixed issues with changing application language - Fixed to show device bonus dialog when applicable
|
|
djidji
Closed beta tester
Posts: 2
|
Post by djidji on May 5, 2020 18:44:59 GMT
High beam assist
Android 10 Samsung S20 Ultra Nextgen Audi A4 B9 2016 sergio
factory settings was "original", after coding to "on" high beam was completely nonoperational. no any error in any module, blue light indicator on dashboard works normally but there is no high beam output. not possible to switch back to "original" code when engine running, it can be codded back only with ignition on without engine running.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on May 5, 2020 21:17:46 GMT
Description of bug : diagnostic change in History file does not give pre and post change in one section.
Just sent myself email from history of my Control Unit 01 Screen shot
as you can see I changed Diagnostic mode from OBD Diagnostic mode to Development mode
however when you look at the history extract it shows following eg not before and after just the current setting I have to look at previous change to work out what it was before.
Diagnostic session Control unit: 01 Engine Value: Development mode Mileage: 50322 km Date: 2020-05-02 16:18
--------------------------------------------------------------- Diagnostic session Control unit: 01 Engine Value: OBD-diagnostic mode Mileage: 50322 km Date: 2020-05-02 16:17
Android software version: 9 Phone: Sony Xperia Dongle variant: Nextgen Car: your vehicle Seat Leon Cupra 280 App profile: username - cupra280.co.uk
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on May 6, 2020 12:36:12 GMT
Description of bug:
Full Backup failed, as reported previously got the first three control units and then carried on and did 0% on each control unit.
However I got this to happen after getting it to work, the difference between the two runs was the sucsesful run was with engine running. Failed run was on car battery showing 11.6v I have certainly seen some reports on VCDS Forums saying you need to have at least 12v to code some control units.
If this is a voltage issue is there any way you can put in a warning or is it simple advise that full backup should always be done with batter at xx level or with engine running
Android software version: 9 Phone: Sony Xperia Dongle variant: Nextgen Car: your vehicle Seat Leon Cupra 280 App profile: username - cupra280.co.uk
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on May 11, 2020 21:45:56 GMT
Description of bug Email of charts causes app to crash. Looking to email old chart, when I go into main chart section (My Car screen) and send an old chart works fine. When I go to control unit 01 and then charts and send an old chart the app opens email box and sends chart but also crashes the app.
and gentle reminder email car info via gmail does not work but does for yahoo mail
Android software version: 9 Phone: Sony Xperia Dongle variant: Nextgen Car: your vehicle Seat Leon Cupra 280 App profile: username - cupra280.co.uk
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on May 12, 2020 14:51:45 GMT
Description of bug's 1/ Been using the dongle with no issue most of the day, last use was trying to connect to Honda Jazz (did not work and issue reported to support). Then went to log onto the Cupra and I get the Create Password screen for dongle when I first try to connect. I closed and logged on again no issue, I have seen this before just not bothered to raise issue.
UPDATE Support have confirmed that they do not support HONDA for fault scan process but they do support FORD.
2/ Statistics although I doubt anybody uses this function when you make long coding changes the count for programming completed does not increase 3/ Whilst trying to connect to the Honda i had to enter the VIN Code (expected) but this was all in lower case and i had to keep going into upper case also once I had entered the correct vin (because OBD11 does not understand the VIN) the screen just goes back to login and you have to try again. If you add the car to the garage it is forced into upper case (can we make the other method the same please) and I got an error message (same for other method please) telling me it could not understand the VIN Code entered (that issue is with support.
4/ Ran full scan (and got errors) from the main scan screen I selected email option Email with details was created but the default email address from settings was not applied, when I did the same from history default name was applied
5/ From history when I go check out the scan results (I have gone from scan screen to history) I can see the scan and correct numbers shown. However when I use the button to open it up I get a blank screen. When I look at other scan results I can see control unit by control unit detail.
Update After I did a clear of errors and went back to history I can now see all the data.
Android software version: 9 Phone: Sony Xperia Dongle variant: Nextgen Car: your vehicle Seat Leon Cupra 280 App profile: username - cupra280.co.uk
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on May 13, 2020 20:40:24 GMT
Description - This is not a bug related to this release but i noticed today for the first time that it is not possible to add descriptions to Subsystems long coding.
Android software version: 9 Phone: Sony Xperia Dongle variant: Nextgen Car: your vehicle Seat Leon Cupra 280 App profile: username - cupra280.co.uk
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on May 15, 2020 9:58:41 GMT
Description - I have been trying to get auto rain closing working on my car (RLFS).
The coding showed i had to tick Bit 1 and Bit 2 of Byte 00 and that took no problem (but not working) But today I tried to just untick Bit 2 and got error (31) Function not availiable. I then tried to just untick Bit 1 and got same error. However when I untick bot then it took the coding change.
Tried the reverse and same issue if I just tick Bit 1 or Bit 2 on there own i get error (31).
Not seen this before is this a bug or a feature of the sub systems.
Android software version: 9 Phone: Sony Xperia Dongle variant: Nextgen Car: your vehicle Seat Leon Cupra 280 App profile: username - cupra280.co.uk
|
|
mmi
Closed beta tester
Posts: 2
|
Post by mmi on May 25, 2020 15:11:09 GMT
Description of bug: Can't split grouped coding description (grayed out top line), neither can delete description (my own, can edit) Android software version: 10 Phone: Nokia 6.1 Dongle variant: Firstgen Car: VW, Transporter, 2018 App profile: Matti
Had created a grouped coding description some time ago. Along new information need to remove grouping as (here bit 5 and 6) the bits are independent.
Tried to be remove the description but can't do that either.
|
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on May 25, 2020 17:20:18 GMT
Description of bug: As per mmi I have reported this before but the same applies to a single entry, I have not found a way to delete an entry that I made, I am able to change details but not remove/delete Android software version: 9 Phone: Sony Xperia Dongle variant: Nextgen Car: your vehicle Seat Leon Cupra 280 App profile: username - cupra280.co.uk
|
|