|
Post by marcot on Jun 6, 2023 5:56:42 GMT
Hi everyone,
I have a 2017 Audi Q2 1.6 stronic, I have fitted the reversing camera (High Line). I coded the ECUs with OBD11 (with iOS), connected the bus, video and the 12v in parallel to the MMI; everything works, it deactivates if it exceeds a certain speed, if I put the gearbox in "P" and if I engage the handbrake, the only problem, when the MMI is turned on, the Q2 logo no longer appears (splash screen), or rather, appears once in ten. If I cut power to the reversing camera, the logo comes back on every power up and if I do a soft reset of the MMI, the logo appears on boot.
Can you help me understand what it depends on?
These are the codings done:
- 19 gateways: Adaptation - Installation List - addition "Reversing Camera"
- 76 Parking Assistant: Long Coding - “Camera type” - enable “Rearview camera”
- 5F infotainment: Adaptation – “Car function list BAP” - VPS_0x0B: activated / VPS_0x0B_msg_bus: databus infotainment
No errors in the ECUs (except 6C calibration).
Thank you!!
|
|
|
Post by marcot on Jun 8, 2023 12:04:35 GMT
I try to simplify my question/doubt 😊 then I give up Of all the operations performed to install the RVC, I still have one doubt, what is the correct value to insert for the parameter of the 5F infotainment control unit: “Car function list BAP - VPS_0x0B_msg_bus”? Infotainment data bus? Or Terminal 15? The RVC was connected with a bridge to the MMI bus, while the +12v in parallel to the quadlock. I've also read some posts on can bus communications by dv52 (Australia), well articulated, but I still can't figure out what the correct value is Thank you!!! sorry for my english
|
|
|
Post by moumoute68 on Jun 10, 2023 17:27:18 GMT
Hello, I would have liked to help you, but I myself have a problem after installing a backup camera.
|
|
|
Post by moumoute68 on Jun 10, 2023 17:30:49 GMT
VIN: WAUZZZGA0HA053753 Voiture: Audi Q2 Année: 2017 Type de carrosserie: SUV Moteur: DFGA Kilométrage: 112955 KM
--------------------------------------------------------------- 09 Central Electrics
Description du système: BCM MQBAB M+ Numéro de logiciel: 5Q0937084CF Version de logiciel: 0236 Numéro de Matériel: 5Q0937084CF Version matériel: H34 Numéro de série: 02001710202952 Nom du ODX: EV_BCMMQB Version ODX: 017001 Codage long: 040000000000000000000000000000000000000000000000000000000000
Sous-systèmes: Description du système: G397_RLFSS Version de logiciel: 0002 Version matériel: H06 Numéro de série: 20372253X81A955555A0 Codage long: 80005E
Description du système: E1 - LDS MQB Version de logiciel: 0032 Version matériel: H06 Numéro de série: 29 01 2017 00000443
Codes d'erreur: B140E13 - Voltage supply, terminal 30, right Open circuit Intermittent Date: 2023-06-07 20:37:01 Mileage: 112922 km Priority: 1 Malfunction frequency counter: 1 Unlearning counter: 141 Terminal 15 status: Off Terminal 50 status: Off Voltage: 12.5 V Outside air temperature: 27.0 °C Status Bremslichtschalter (HW): Off Status Bremslichtschalter (CAN): Off Off: not activated Parking light: not activated Automatic high beam assist: operated Low beam: not activated Parking light left: not activated Parking light right: not activated Letzte Weckursache/ Werte [00;2E]: gültiges Funktelegramm CAN-Bus_aktiv: Off B142313 - Voltage supply for terminal 30 P(ower) Open circuit Intermittent Date: 2023-06-07 20:36:16 Mileage: 112922 km Priority: 1 Malfunction frequency counter: 1 Unlearning counter: 141 Terminal 15 status: Off Terminal 50 status: Off Voltage: 12.4 V Outside air temperature: 27.5 °C Status Bremslichtschalter (HW): Off Status Bremslichtschalter (CAN): Off Off: not activated Parking light: not activated Automatic high beam assist: operated Low beam: not activated Parking light left: not activated Parking light right: not activated Letzte Weckursache/ Werte [00;2E]: gültiges Funktelegramm CAN-Bus_aktiv: Off
17 Dashboard
Description du système: FBenRDW Numéro de logiciel: 8V0920790 Version de logiciel: 0047 Numéro de Matériel: 8V0920790 Version matériel: H14 Nom du ODX: EV_DashBoardFPKAU37X Version ODX: 001023 Codage long: 04FF20E46F9C00080085E8041000200000000000
Codes d'erreur: U112100 - Databus missing message static Date: 2023-06-05 17:51:57 Mileage: 112864 km Priority: 6 Malfunction frequency counter: 1 Unlearning counter: 99 U112100 - Databus missing message static Date: 2023-06-05 17:51:57 Mileage: 112864 km Priority: 6 Malfunction frequency counter: 1 Unlearning counter: 99
6C Rear View Camera
Description du système: RVC Compact Numéro de logiciel: 5Q0980556B Version de logiciel: 0231 Numéro de Matériel: 4M0980556A Version matériel: H18 Nom du ODX: EV_CamSysRVRVCPANAMQBAB Version ODX: 006009 Codage long: 0273010100002001400060
Codes d'erreur: B201000 - No basic setting static Date: 2023-06-07 22:21:44 Mileage: 112922 km Priority: 5 Malfunction frequency counter: 1 Unlearning counter: 101 ---: Passive
|
|
|
Post by marcot on Jun 12, 2023 7:46:15 GMT
Hi moumoute68, unfortunately I'm not an expert, the only thing I can tell you is that the 6C error is only related to the calibration, while for the configuration, in my first post the steps I took for the coding. Everything works for me, except that the MMI startup screen no longer appears. Good day
|
|