Alternating Blinker/DRL

[shahwant96]

Hello,

I just bought a 2014 Audi A3, and the previous owner had coded the turn signals and DRLs on the front headlights to alternate, like the “urban joke” feature for the taillights. How can I get rid of this? I want the DRL to dim when that side’s turn signal is on, and turn back to full brightness when the turn signal is off again. I have the Xenon headlight package if that helps.

Would appreciate the help.

Many thanks!

- Tariq

2014 Audi A3 / 1.4T / 4-dr / Xenon Headlights + Panoramic Sunroof

[dv52 (Australia)]

shahwant96: Post-up screenshots of Leuchte2SL VLB10 and Leuchte4TFL LB4. To be clear, I need to see the values for ALL 19 x adaptation channels for each Leuchte-set in the pictures

Don

[shahwant96]

Here are the requested screenshots.  Thank you for your help!

[shahwant96]

Hey Don,

I haven’t heard back yet - would really appreciate the help. Thank you!

- Tariq

[dv52 (Australia)]

"I haven’t heard back yet"??
 

Tariq: hmm...... Cleary you are keen to resolve this matter - but please understand that I don't work for OBD11 and I receive a little less than $0 for each response I make in answering forum member's questions. 

Most of the moderators on this forum are volunteers and we do this stuff when we get the time (and when we have an interest to log-in)!! So, if I don't respond to a post within a time considered reasonable by a forum member - it's because I'm enjoying being the real me (which is far more important than my virtual persona as DV52)!!

OK - Ive looked at your screenshots. Based on my understanding of the very strange changes made to this car - I'm guessing that the original factory settings are these:

Leuchte2SL VLB10
Lichtfunktion A 2 > Tagfahrlicht
Lichtfunktion B 2 > Coming Home oder Leaving Home aktiv
Dimmwert AB 2 > 100
Lichtansteuerung HD AB 2 > Always
Lichtfunktion C 2 > Blinken links aktiv (beide Phasen)
Lichtfunktion D 2 > not active
Dimmwert CD 2 > 0
Dimming Direction CD 2 > minimize
Lichtfunktion E 2 > Standlicht allgemein (Schlusslicht; Positionslicht; Begrenzungslicht)
Lichtfunktion F 2 > Parklicht links (beidseitiges Parklicht aktiviert li & re)
Dimmwert EF 2 > 30
Dimming Direction EF 2 > maximize
Lichtfunktion G 2 > not active
Lichtfunktion H 2 > not active
Dimmwert GH 2 > 0
Dimming Direction GH 2 > maximize

Leuchte3SL VRB21
Lichtfunktion A 3 > Tagfahrlicht
Lichtfunktion B 3 > Coming Home oder Leaving Home aktiv
Dimmwert AB 3 > 100
Lichtansteuerung HD AB 3 > Always
Lichtfunktion C 3 > Blinken rechts aktiv (beide Phasen)
Lichtfunktion D 3 > not active
Dimmwert CD 3 > 0
Dimming Direction CD 3 > minimize
Lichtfunktion E 3 > Standlicht allgemein (Schlusslicht; Positionslicht; Begrenzungslicht)
Lichtfunktion F 3 > Parklicht rechts
Dimmwert EF 3 > 30
Dimming Direction EF 3 > maximize
Lichtfunktion G 3 > not active
Lichtfunktion H 3 > not active
Dimmwert GH 3 > 0

Dimming Direction GH 3 > maximize

Don

[shahwant96]

Hi Don,

I apologise for my impatience, but this stupid blinker was just really getting on my nerves.

Ok, so I did all the below adaptations and it worked except for the fact that when I signal left, both DRLs dim, and when I signal right neither of them dim. How can I have it so that just the side with the active blinker dims?

I have attached a new set of screenshots for you to see.

Thank you so much!

- Tariq

[shahwant96]

Hi Don,

Sorry - I had a look at the adaptations I made and I had set Leuchte3SL VRB21 > Lichtfunktion C 3 > Blinken rechts aktiv (beide Phasen) to be “Blinken links activ” by mistake.

All works perfectly now.

Thanks so much Don!