|
|
Post by andreamala on Dec 9, 2023 21:01:30 GMT
Why doesn't my passenger door exit light come on?
Coded done
Pin 16 positive
Pin 5 negative
|
|
|
|
Post by dv52 (Australia) on Dec 9, 2023 21:58:40 GMT
andrea : Hi. I don't know the answer to your question - in part because your post contains insufficient information and in part because I don't understand what is meant by "passenger door exit light". There are multiple lights on the door panel and it's very easy for folk to use different names for these lights. That said, according to my wiring diagrams for a mk7.5, pin #T32a /16 (being pin #16 on the connector that has 32 x pin positions) on the passenger side door module is connected to W67 Light conductor for front left sill panel molding ambient lighting (item 8 in the picture below). Is this what you are calling the "passenger door exit light"? If not, which of the lamps in the picture below is this light?
Don
|
|
|
|
Post by vwjap on Dec 9, 2023 23:46:22 GMT
Where did you get the exit lights from?
You checked the plug is the right way round in the light? (LED will only work if voltage is the correct way round)
You checked there’s voltage on the light connector?
How did you wire up the connector? (5 and 16)
|
|
|
|
Post by andreamala on Dec 10, 2023 9:19:30 GMT
andrea : Hi. I don't know the answer to your question - in part because your post contains insufficient information and in part because I don't understand what is meant by "passenger door exit light". There are multiple lights on the door panel and it's very easy for folk to use different names for these lights. That said, according to my wiring diagrams for a mk7.5, pin #T32a /16 (being pin #16 on the connector that has 32 x pin positions) on the passenger side door module is connected to W67 Light conductor for front left sill panel molding ambient lighting (item 8 in the picture below). Is this what you are calling the "passenger door exit light"? If not, which of the lamps in the picture below is this light?
Don
Item 7 in the picture Light in door's driver turn on Same pin and light |
|
|
|
Post by dv52 (Australia) on Dec 11, 2023 1:24:58 GMT
OK - Item 7 is sometimes called the "puddle lights". I assume that you coded Byte01, Bit 2 on the the passenger-side door module As per vwjap suggestion - check that the fitting leads haven't been reversed
Don
|
|
|
|
Post by andreamala on Dec 11, 2023 8:18:42 GMT
I have already assembled and coded it on the left driver's side and everything works, but on the right side it gives me an error and won't turn on.
I coded "door exit light" - active
|
|
|
|
Post by vwjap on Dec 11, 2023 9:11:03 GMT
Plug the drivers side light (known working)into the passenger side wiring and see if it’s the light, check the voltage, check the polarity
|
|
|
|
Post by andreamala on Dec 11, 2023 11:45:44 GMT
Light's driver not work.
|
|
|
|
Post by vwjap on Dec 11, 2023 18:10:20 GMT
So again, have you checked polarity?
Also how did you connect to connector and what joins did you use?
|
|
|
|
Post by andreamala on Dec 14, 2023 8:06:54 GMT
For ground I used Brown wire
Should I use Brown/yellow wire?
|
|
|
|
Post by vwjap on Dec 14, 2023 12:19:41 GMT
Brown is fine,
Have you got a volt meter to check the voltage?
But what did you use for joints? Scotch clips, chocolate block?
|
|
|
|
Post by andreamala on Jan 7, 2024 12:53:50 GMT
Ground wire broken on the original wiring
|
|
