|
|
Post by ofektal8 on Dec 11, 2018 16:21:31 GMT
Park-Pilot, the virtual stroller disappeared from the Discover Pro screen, when the proximity sensors were activated.
I have been playing some things with OBDEleven, later I left it as it was because I had an error in "rear camera" (I do not have a camera), the errors have disappeared.
But when entering the tunnel of the garage, I realized that the sensors activate the sounds of proximity to an obstacle, but now I do not see the image of the virtual car with the yellow or red bars according to the proximity on the screen of discover Pro.
In Car_Funtion_List_BAP_Gen2, I have activated the "Parking_assist_0x0A"
In Car-Menu, I have the menu activated and the options of volume and automatic activation work.
I have used the "Optical Parking System" application, but the virtual car image has not been activated either.
The problem is that the virtual car image has disappeared on the Discover Pro screen.
I could use a help, please.
Thanks and best regards.
Edito .: To add that I have also activated the "Vehicle path display" application, and it still does not work.
It does not appear on the screen of discover the virtual cohesion, the sensors work perfectly and sound warning of the obstacle.
Currently I have both applications powered and it does not work; the virtual car does not appear when parking on the discover screen. Before it appeared.
I think I've already commented, I DO NOT HAVE A REAR CAMERA
Can you please post a scan? |
|
|
|
Post by ofektal8 on Dec 11, 2018 20:48:57 GMT
Can you please post a scan?
Thanks for your help. I guess you mean a scan with VCDS, tomorrow maybe I can get it. And it will be the complete 5F module ...  Thanks and best regards. Scan of 5F and the park assist module. And You can make a scan with obdeleven too but VCDS is fine. The coding for front and rear park assist is Coding 19 CAN Gateway - Installation List - 10 Park/Steer Assist 5F Infotainment - Adaptation - set all to active Vehicle function list BAP-parking_assist_0x0A Vehicle menu operation-menu_display_pdc Vehicle menu operation-menu_display_pdc_over_threshold_high |
|
|
|
Post by ofektal8 on Dec 12, 2018 16:19:28 GMT
Scan of 5F and the park assist module. And You can make a scan with obdeleven too but VCDS is fine. The coding for front and rear park assist is Coding 19 CAN Gateway - Installation List - 10 Park/Steer Assist 5F Infotainment - Adaptation - set all to active Vehicle function list BAP-parking_assist_0x0A Vehicle menu operation-menu_display_pdc Vehicle menu operation-menu_display_pdc_over_threshold_high
Thank you very much for your help
I already see the vehicle on screen when the Park-Pilot activates
It works Perfectly, but .............., the lines of the direction of rotation of the steering wheel do not appear in the representation of the screen; I used to leave.
Algho like that, although I had to put straight lines, although they are curved lines.
A little more help, please, to leave it as it was in the factory.
Thank you very much again and kind regards.
MERRY CHRISTMAS
Hey, Glad that worked. Have you tried using the app for vehicle path display? If that does not work, go to the park assist module and check if path display is activated. |
|
|
|
Post by ofektal8 on Dec 12, 2018 18:33:04 GMT
Hey, Glad that worked. Have you tried using the app for vehicle path display? If that does not work, go to the park assist module and check if path display is activated.
Hello good afternoon I have activated it from the extended coding of the Parking Assistant Module, in Byte 2, activating bite 0. I have not dared to do it from the application "Vehicle Patch Display", because yesterday I activate a rear camera, and I gave a failure to scan.  It could be activating Rail Indication, in the assisted parking module .. 
 I do not want to touch anything, so as not to mess it up again. Thank you very much for your help. If my translation is correct, then what you marked in red says Without path display. So to have path display just change it to "With Path Display". Nothing bad can happen if you do that. |
|
|
|
Post by ofektal8 on Dec 12, 2018 20:55:44 GMT
If my translation is correct, then what you marked in red says Without path display. So to have path display just change it to "With Path Display". Nothing bad can happen if you do that.
Goodnight
Thank you very much, I activated the "Lane indication", and it WORKS ...... !!!!  
Thank you very much again for your help, really, I had a huge headache with this issue.
Now I only have one little doubt:
In the history I see that the original extended coding of the control unit of the Parking Assistant was: 00 71 05 10 11 And after the new coding, it is now: 00 51 05 10 11 Change the value of 7 to 5, (it would be byte 01) whose value is now 51. I would have to put that value in 71 .. How could I do ? Thank you very much for your attention and for your patience.
Awesome!. I Didnt understand your question. and if everything works now then you shouldnt be worried about it. |
|
|
|
Post by ofektal8 on Dec 12, 2018 23:59:49 GMT
Awesome!. I Didnt understand your question. and if everything works now then you shouldnt be worried about it.
Goodnight
Yes, now everything works, but my doubt is that as the original coding (History), Byte 01 = 71, and now Byte 01 = 51, I'm not sure if I should put it as it was originally encoded, that is by modifying Byte 01 and activating bit 5, so that it was originally = 71
Thanks and kind regards.
Oh, Byte 1 Bit 5 is What you just Changed, Its for the Path Display. So dont change it back. No Problem. |
|
|
|
Post by ofektal8 on Dec 13, 2018 16:04:34 GMT
Oh, Byte 1 Bit 5 is What you just Changed, Its for the Path Display. So dont change it back. No Problem.
Good morning Sure enough, you're absolutely right, I looked at it and it was already activated, and the coding was the original. Everything working perfectly. Thank you very much for your help. A cordial greeting and Merry Christmas for the entire Forum. No Problem. My Pleasure |
|
|
|
Post by caritaxd24 on Jan 9, 2019 5:41:54 GMT
Hi. I have a similar problem. When I put the car in R... (I have rear view camera) I only see rear view camera. No vehicle path display in vertical. At the bottom have an adviser that says Park Pilot isn’t activated. When I press button beside gear shift I got the vehicle path display with yellow line of wheel directions but only when the car aren’t in R. I went to module 5F and tried to deactivating Rear view camera and vehicle path obviously works fine also moving forward and backward. When I feel tat I’m too close to make it works perfectly. Any ideas for Vertical vehicle graphics when goes in R? And for advisory Park pilot not activated.
|
|
|
|
Post by ofektal8 on Jan 9, 2019 11:24:28 GMT
Hi. I have a similar problem. When I put the car in R... (I have rear view camera) I only see rear view camera. No vehicle path display in vertical. At the bottom have an adviser that says Park Pilot isn’t activated. When I press button beside gear shift I got the vehicle path display with yellow line of wheel directions but only when the car aren’t in R. I went to module 5F and tried to deactivating Rear view camera and vehicle path obviously works fine also moving forward and backward. When I feel tat I’m too close to make it works perfectly. Any ideas for Vertical vehicle graphics when goes in R? And for advisory Park pilot not activated. In the park assist module, what did you select in camera type? It should be the same as in pic.  |
|
|
|
Post by caritaxd24 on Jan 16, 2019 3:32:48 GMT
Yes. I have rear view camera. If I disable only get OPS. When tried with camera 360 its the same as RVC and when I tried with Japanese version camera the same as RVC. Nothing.
|
|
|
|
Post by gianry on Apr 1, 2019 10:28:12 GMT
I've the same with the same hardware (standard rear camera and ops module hw " A" ) and the same issue.
I think the virtual path display require a particular gateway and some other hardware ( active ABS sensors ?? )
PS: in my OBD eleven app the long coding isn't shown in menu like previuos picture but only bit and byte view ; how can I use long coding with interactive menu ?
thanks
|
|
|
|
Post by vwjap on Apr 1, 2019 10:52:39 GMT
If you haven’t got the yellow lines (not green) on the camera then they cannot be switched on, that’s the difference between a highline and lowline camera
Press the 0/1 in the top right corner
|
|
|
|
Post by gianry on Apr 1, 2019 11:27:34 GMT
so I need highline camera to activate virtual path display for parking sensor ?
|
|
|
|
Post by vwjap on Apr 1, 2019 11:31:54 GMT
No not for the parking sensors, but yes for the lines in the camera  |
|
|
|
Post by gianry on Apr 1, 2019 11:59:39 GMT
I'm asking for the parking lines ... so which is the issue in my car the lines aren't visible ?
|
|
|
|
Post by vwjap on Apr 1, 2019 12:37:36 GMT
Copy the settings in the picture above Making sure the ones in yellow are the same  |
|
|
|
Post by gianry on Apr 1, 2019 12:44:57 GMT
Ok,I’ll let you know sooner
|
|
|
|
Post by gianry on Apr 1, 2019 19:19:14 GMT
8’ve checked now th settings but it seems to be good .
THe only difference is that I have “ OPS VIEW” and not “ 360 OPS VIEW”
|
|
|
|
Post by vwjap on Apr 1, 2019 19:49:25 GMT
Are you talking about front park pilot, or the car on the right of the screen when the camera is on
|
|
|
|
Post by gianry on Apr 1, 2019 20:18:07 GMT
|
|
|
|
Post by vwjap on Apr 1, 2019 20:56:05 GMT
Suspension data bus? What have you linked to the suspension data bus?
|
|
|
|
Post by gianry on Apr 1, 2019 21:24:45 GMT
Nothing , I don’t know which is that error .
|
|
|
|
Post by vwjap on Apr 1, 2019 21:42:44 GMT
What settings you changed? Or apps?
|
|
|
|
Post by gianry on Apr 2, 2019 6:35:41 GMT
I’ve not changed any settings except as shown in the picture I’ve uploaded
In any case why I don’t see the car path lines with correct parameters ?
|
|
|
|
Post by gianry on Apr 2, 2019 8:01:41 GMT
I’m not sure I’ve explained what I ‘ d like to view . Is it possible to have the yellow lines shown in picture below ?. I’ve rear standard rear camera too  |
|
|
|
Post by ofektal8 on Apr 2, 2019 11:27:10 GMT
When you shift from reverse to D Does the camera screen go away and you see the Park assist display?
Thats how it was on my car.
|
|
|
|
Post by gianry on Apr 2, 2019 11:55:33 GMT
yes, I see till the car reaches 15 kmh but without the yellow lines that represents the steering wheeel
|
|
|
|
Post by gianry on Apr 2, 2019 12:17:05 GMT
I'm checking again the coding of parking module; I see the byte 01 isn't "51" but "71"
I've seen in the other coded screenshot it would be 51 with "vehicle path display " enabled.
Why in my module isn't right ?
|
|
|
|
Post by dv52 (Australia) on Apr 2, 2019 12:35:02 GMT
I'm checking again the coding of parking module; I see the byte 01 isn't "51" but "71" I've seen in the other coded screenshot it would be 51 with "vehicle path display " enabled. Why in my module isn't right ? hmm............ difference between hex51 and hex71 is setting high bit 5 (see below)
|
|
|
|
Post by gianry on Apr 2, 2019 12:42:38 GMT
I've changed bit5 with obdeleven to 1 but long coding is that. Why ?
|
|
