|
|
Post by vwjap on Apr 2, 2019 12:53:59 GMT
Mines 71, I noticed anything I did with the rear camera I had to reset the mmi to get it to work, when was the last time you reset it?
|
|
|
|
Post by gianry on Apr 2, 2019 12:59:51 GMT
are you talking to reset discover pro unit ? in which way ?
|
|
|
|
Post by dv52 (Australia) on Apr 2, 2019 13:00:05 GMT
I've changed bit5 with obdeleven to 1 but long coding is that. Why ? see the addition to my post for the obd11 screen |
|
|
|
Post by gianry on Apr 2, 2019 13:45:45 GMT
you haven't enabled the wheels sensor with detection of direction;
|
|
|
|
Post by vwjap on Apr 2, 2019 15:08:54 GMT
He has on his screen,
|
|
|
|
Post by gianry on Apr 2, 2019 17:03:43 GMT
In its module the value is “ not installed “ in mine the value is “installed “
|
|
|
|
Post by ofektal8 on Apr 2, 2019 17:16:02 GMT
In its module the value is “ not installed “ in mine the value is “installed “ Ive never seen it enabled on any car. |
|
|
|
Post by vwjap on Apr 2, 2019 17:25:02 GMT
I’ve never seen it installed either
|
|
|
|
Post by gianry on Apr 2, 2019 19:56:52 GMT
Nothing !!! I’ve disabled also the wheel sensor parameter but I don’t see the lines of the steering wheel position
|
|
|
|
Post by ofektal8 on Apr 3, 2019 6:16:31 GMT
Just so yo know, the dynamic lines only work on this screen (attached) and not on the camera screen( as you have a lowline camera) And the dynamic lines only work With the hand brake off. Maybe the errors in your module are causing it. When you activate park assist does the button blink?  |
|
|
|
Post by gianry on Apr 3, 2019 9:54:12 GMT
I 've tried to switch off the rear view and I see the imege posted but without dynamic lines
|
|
|
|
Post by ofektal8 on Apr 3, 2019 17:31:22 GMT
I 've tried to switch off the rear view and I see the imege posted but without dynamic lines But is the park assist button blinking when park assist is active? Because if it is the lines will not work until you fix the errors in the module. Also, Go to Module 5F, Adaptations, Car function list bap, and find Parking assist. It should look like that.  |
|
|
|
Post by vwjap on Apr 3, 2019 17:57:51 GMT
That’s what I thought about the suspension bus error, but he said he hadn’t done any mods,
|
|
|
|
Post by gianry on Apr 5, 2019 12:08:03 GMT
I've blinkinng button as I've not just installed front sensors. I'll go to fit them tomorrow
|
|
|
|
Post by vwjap on Apr 5, 2019 12:31:22 GMT
Hold on, so your asking why it’s not working when you have half the kit not installed?
|
|
|
|
Post by ofektal8 on Apr 6, 2019 8:34:45 GMT
Hold on, so your asking why it’s not working when you have half the kit not installed? As vwjap said, everything must be installed and working for the path diaplay to show. |
|
|
|
Post by gianry on Apr 6, 2019 14:09:58 GMT
Hold on, so your asking why it’s not working when you have half the kit not installed? Excuse me !!! I've just finished to fit the front sensors and now I'm able to see the virtual path on screen !!! thanks |
|
|
|
Post by vwjap on Apr 6, 2019 16:52:13 GMT
🤦♂️ Glad that’s over 😂🤣😂
|
|
|
|
Post by gianry on Apr 11, 2019 20:02:18 GMT
The park pilot works well but I’ve always the fault code : suspension data bus no communication
Fault code u10ac00
Intermittent
Priority 6
Why !?
|
|
|
|
Post by ofektal8 on Apr 11, 2019 20:16:03 GMT
I 've tried to switch off the rear view and I see the imege posted but without dynamic lines But is the park assist button blinking when park assist is active? Because if it is the lines will not work until you fix the errors in the module. Also, Go to Module 5F, Adaptations, Car function list bap, and find Parking assist. It should look like that. Have you tried this step? Notice that park assist msg bus is set to Terminal 15 and not suspension data bus. |
|
|
|
Post by gianry on Apr 11, 2019 21:11:03 GMT
Tomorrow I'll check that
I remember to have set all the parameters in 5f module.
thanks
|
|
|
|
Post by ofektal8 on Apr 13, 2019 6:16:10 GMT
Have you tried this step? Notice that park assist msg bus is set to Terminal 15 and not suspension data bus.
Hello
Sorry interruption Ofektal8
In my BCM I have the option VPS_0x0B (under Parking Assist) Deactivated and the data bus in Infotainment.
What controls this VPS option ..  I do not have Rear or Front Camera, only the Park-Pilot. Thanks and sorry again the intrusion in the post. A cordial greeting. You enable VPS When you have a Highline reverse camera, with the moving guidelines. |
|
|
|
Post by gianry on Apr 13, 2019 19:33:38 GMT
But is the park assist button blinking when park assist is active? Because if it is the lines will not work until you fix the errors in the module. Also, Go to Module 5F, Adaptations, Car function list bap, and find Parking assist. It should look like that. Have you tried this step? Notice that park assist msg bus is set to Terminal 15 and not suspension data bus. I've checked but the 5f module parameters are correct ; I don't know why in the parking module there is the fault code about suspension data bus ( SAE code U10AC00 - Event code C00400 ) please help me could you send me the complete coding parameters of the parking module 8K thnka |
|
|
|
Post by gianry on Apr 13, 2019 20:24:29 GMT
If my translation is correct, then what you marked in red says Without path display. So to have path display just change it to "With Path Display". Nothing bad can happen if you do that. have you got the Advanced cruise control (ACC) ? |
|
|
|
Post by smeve196 on Oct 23, 2020 18:48:55 GMT
HELP i have literally tried every setting here and activated everything thats been discussed but still no parkpilot display. I don’t even have a parking and manoeuvring option in settings on the MIB?!
|
|
|
|
Post by rashu786 on May 16, 2021 20:32:24 GMT
Hi Guys newbie here I have an Audi S3 8V facelift I have front parking and rear parking sensors and rear view camera my park pilot aid seems to have disappeared after having the camera retrofitted if I press P on the console it shows the reverse camera but I do not want it to do that as I have the reverse gear for that any help would be appreciated
|
|
|
|
Post by dv52 (Australia) on May 16, 2021 23:32:04 GMT
@rashu: notwithstanding that your Audi is built on the same MQB platform as the cars in this sub-forum, you should post your question(s) in the appropriate build-year on Audi A3 part of the forum.
And when (if) you do this - please be more expansive in the description of the problem. I'm not sure, but I think that you are asking 2 x separate questions - maybe?
Your latter point about "pressing the P on the console" is normal; the console switch does exactly the same things as selecting reverse- it's designed that way and AFAIK it can't be coded to operate differently to the reversing process
Don
|
|
ludz
New Member
Posts: 5
|
Post by ludz on Sept 19, 2021 9:23:30 GMT
I can't see my display when reversing. I can hear it but nothing on the screen. It had been working but no joy. Also, my fuel flap will not open when unlocking the car. When I try to select it will not allow me to on the obd11. It says there is an error and my boot does not open properly lol, mode button no longer works........ ?? HELP I have a 15 reg Leon FR |
|
|
|
Post by dv52 (Australia) on Sept 19, 2021 21:38:31 GMT
ludz. So- if you suspect that the problems started after coding changes were made to the car - look in History for any related records and reverse settings back to "old value". If the problem arose otherwise, post-up a copy of the error details Don
|
|
ludz
New Member
Posts: 5
|
Post by ludz on Sept 28, 2021 6:58:44 GMT
Hi Don,
I have looked but nothing jumps out. Would you know what it should be under on the OBD11?
|
|
