|
|
Post by florian on Aug 1, 2019 23:14:53 GMT
Hello
I need your skills friends, I found a tutorial for the wireless charger for tiguan, so I followed the tutorial to the letter but it does not work and I have questions, (first in the tutorial I put you the link of the tutorial and the part which concerns us) the guy talks about being connected to the PIN 14 of the BCM block B which has 73 pin, except that I have 46 pin in the B and 73 in the A and C, so that's already a problem, what do you think? In addition it says if the pin 14 of the block B is taken added anyway the thread, this existing thread concerns the Keyless, but I do not have Keyless and the pin 14 is already taken, second question, then he says to connect to the Farkra in 5 and 11 but I do not know what color I have to plug in, there are several different color connector on the farkra, thank you for your help
"Interface:
- pin 1: Power. 0,5mm red/blue to fusebox (interconnects with same colored wire from amplifier)
- pin 2: Power on signal from infotainment unit. 0,5mm yellow/red to grey connector on infotainment unit pin 5 (interconnects with same colored wire from amplifier)
- pin 3: Data/LIN bus from infotainment unit. 0,5mm yellow/blue to grey connector on infotainment unit pin 11
- pin 4: Ground. 0,5mm brown to ground (i used another bundle of ground wires near the bottom of the A-pillar)
- pin 5: No idea what it does. 0,5mm white to 73-pin plug B pin 14 on BCM (this pin is already in use if you have keyless access. in that case this goes to the Kessy control unit. Strip a piece of isolation and connect to existing wire.)
- violet fakra connector on interface to black fakra connector on amplifier
If you dont need the connection to the external antenna, you could also skip the whole amplifier and antenna part and just hook up the interface.
For the install I removed the following (and not necessarily in this order, check the manual):"
forums.ross-tech.com/showthread.php?12055-5F-(Discover-Pro-Gen2)-coding-Comfort-Telephone-(Qi-charger-signal-booster)/page2
|
|
|
|
Post by dv52 (Australia) on Aug 2, 2019 1:24:42 GMT
^^^ hmm...... I apologize at the outset because I'm not much help - but some comments below for your consideration:
Pin 3 (data/LIN bus from infotainment unit) :I don't believe that the infotainment CAN bus on a mk7 bus uses LIN protocol. This said, the MIB is connected to the other CAN data bus networks via the data bus diagnostic interface J533 (what OBD11 calls the Gateway module @ address hex19) and this module does have a LIN facility - it's on pin# 14 on the module connector. But whether this is the same LIN as per the instructions in your link is a long stretch of deduction - because there are multiple LIN lines on MQB vehicles and each LIN wire ("LIN" is a single wire protocol) has a separate function to its colleague wire.
BCM pin #14: Assuming that this is the same pin on both the mk7 and the Tiggy is again a long stretch of logic. On a mk 7, BCM pin #14, Socket B is the Bonnet contact switch -F387. Like "MasterTommy" (the author of the instructions in your link), I also have no idea what this pin does on a Tiggy BCM!
Don
|
|
|
|
Post by florian on Aug 2, 2019 11:09:31 GMT
Bonjour mon ami, merci de me répondre, cela ne vous dérange-t-il pas que nous suivions ce tutoriel depuis le début? Parce qu'un ami de France a réussi à le faire sur son golf 7 mais il ne me répond pas, je lui explique, j'ai connecté la masse en dessous du BCM il y a plusieurs masse connectée, j'ai branché, j'ai branché le + sur la boîte à fusibles avec un gros fusible de 10 ampères, alors, la broche 14 du bloc "B" du BCM, et après je l'ai branché sur le connecteur bleu du farkra celui où est connectée la caméra de recul, respectivement en 5 et 11, c'est que logique?
Translated with google translator:
Hello my friend, thank you for answering me, does not it bother you that we follow this tutorial from the beginning? Because a friend from France managed to do it on his golf 7 but he does not answer me, I explain him, I connected the mass below the BCM there are several mass connected, I connected,
I plugged the + on the fuse box with a big fuse of 10 amps, then, the pin 14 of the block "B" of the BCM, and after I connected it on the blue connector of the farkra the one where is connected the backup camera, respectively in 5 and 11, is that logical?
|
|
|
|
Post by dv52 (Australia) on Aug 3, 2019 1:27:16 GMT
^^^^ Florian: Again my problem is my deplorable lack of French language skills!! I really can't add anything more to my previous comments - perhaps the picture below will be of assistance. Don  |
|
|
|
Post by florian on Aug 3, 2019 10:49:05 GMT
Okay my friend, yesterday the charger market you see? and today it does not work at all, you could tell me where I have to place it on the fuse box according to you and especially I put a fuse of how much? 10/15/20/25?
Thanks to you
|
|
|
|
Post by florian on Sept 23, 2019 20:05:32 GMT
Hi friends, I have a problem with the charger, it loads, I have the icon on the screen of the 5f, but it never lights as the phone charges, I do not understand why. I checked everything today for the charger, so look at the problem. When I disconnect the MIB in gray, the "PIN11" and I leave the "PIN5" connected, the charger continues to charge and still not the icon that turns on, and if I reconnect PIN11, it does not change anything So there is a problem with this PIN11 wire
![]()   |
|
|
|
Post by dv52 (Australia) on Sept 23, 2019 23:25:19 GMT
Hi friends, I have a problem with the charger, it loads, I have the icon on the screen of the 5f, but it never lights as the phone charges, I do not understand why. I checked everything today for the charger, so look at the problem. When I disconnect the MIB in gray, the "PIN11" and I leave the "PIN5" connected, the charger continues to charge and still not the icon that turns on, and if I reconnect PIN11, it does not change anything So there is a problem with this PIN11 wire
florian: Bonjour once again!! After you physically installed the wireless charger - did you make any changes to the hex5F module to tell it to start using the new equipment? For example - here are the Adaptation channels that have the term "wireless charging" in the hex5F module (note: I've shown the factory default values after the adaptation channel names as " >xxxx" and I've also made some suggestions for how you might change these values - BUT MY SUGGESTIONS ARE PURE GUESSES!!):
Installation list: specified installations-Wireless Charger 1>no (perhaps "yes"?)
specified installations-Wireless Charger 2>no (OR, perhaps "yes'?)
Vehicle function list BAP 2nd generation:
expansion-wireless_charging_0x48 >not activated (don't change?)
expansion-wireless_charging_0x48_msg_bus >not activated (perhaps "Comfort data bus"?) Vehicle menu operation: second generation:
extension-menu_wireless_charging > not activated (perhaps "activated"?)
extension-menu_wireless_charging_after_disclaimer >not activated (don't change?)
extension-menu_wireless_charging_clamp_15_off >not activated (don't change?)
extension-menu_wireless_charging_over_threshold_high >not activated (perhaps "activated"?)
extension-menu_wireless_charging_standstill >not activated (don't change?) And here are instructions for enabling the software switch for wireless charging in the hex5F module's long code. After you complete the instructions, you should see that Byte 15, Bit 5 is set to "1" in the long-code string: Again, these are just suggestions - I've not done this exercise, myself
Don
|
|
|
|
Post by florian on Sept 24, 2019 18:08:01 GMT
Hi DV52 again thank you for your help and your answer, I will try what you tell me, but is it normal that with the thread of the pin 17 unplugged the charger still charge and that despite that I plug it, nothing exchange?
|
|
|
|
Post by dv52 (Australia) on Sept 24, 2019 21:01:19 GMT
^^^I don't know the answer to your question - which I assume is about pin 11 (not pin17)
Don
|
|
|
|
Post by florian on Nov 25, 2019 21:48:54 GMT
Hi all, well and good I went around the question, I tried everything to code, even with Odis, and still no confirmation message when the phone loads, I tried everything, the connections are good, but nothing to do, the phone charges but no confirmation message
|
|
|
|
Post by Carolco on Nov 26, 2019 22:30:14 GMT
hello, In the seat leon works fine like this.
Pin 1... Positive direct
Pin 2... pin 2 conector grey infotainment.
Pin 3... pin 11 conector grey infotainment.
Pin 4,,, Masa
|
|
|
|
Post by florian on Nov 27, 2019 22:15:26 GMT
hello, In the seat leon works fine like this. Pin 1... Positive direct Pin 2... pin 2 conector grey infotainment. Pin 3... pin 11 conector grey infotainment. Pin 4,,, Masa Hi my friend, you say to connect on wire 2 of the "gray" socket, but everyone says 5 and 11, are you sure for 2? Because I did not test on the 2 Hi my friend, you say to connect on wire 2 of the "gray" socket, but everyone says 5 and 11, are you sure for 2? Because I did not test on the 2 |
|
|
|
Post by Carolco on Nov 27, 2019 23:35:45 GMT
Taste by owner of Leon 5F
|
|
|
|
Post by florian on Nov 28, 2019 21:23:16 GMT
Taste by owner of Leon 5F Hi my friend, I went down in the car to change that, so I tested the wire that was plugged into the gray connector 5, on the 2, it did not put a charge confirmation message on the screen and the charger does not charge anymore, so I put this wire back in 5, the charger went back to market, so I tried with the second wire which is at 11 on the gray connector, so this wire that it is plugged in any unplugged does not change anything on the charger, the charger continues to walk if the wire 11 is plugged in or not, I tried to put it on the 2 it did not change anything message from confirmation, so for summary, if I disconnect the wire 5 nothing works, so I reconnect the 5, but the 11 it is useless today in my car because or it does not change and nothing , do you think you can help me now with that? |
|
|
|
Post by Carolco on Nov 28, 2019 23:10:18 GMT
|
|
|
|
Post by florian on Nov 29, 2019 12:29:29 GMT
I just read the first post, it gives the same connections as golf 7, in the connector 5f gray, it says 5 and 11 as I did, but I do not understand why I do not have the signal, you would you tell me?
|
|
|
|
Post by fransooto47 on May 10, 2024 8:56:58 GMT
Hello!
Sorry if I miss anything, it is my first time at a forum, I have read all the posts, although I am trying to connect a wireless charger like the one mentioned.
I already connected the positive and ground wire, but I am not being able to find where the grey connector is, and if it is necessary to connect the white wire, as my car is keyless.
It would be like a miracle if you could help me friends.
Will be waiting for an answer.
Thanks!
|
|
