|
|
Post by rafaelravi on Nov 28, 2016 19:35:40 GMT
not my coding but i did think it would be nice to share  link to original post below Here is the coding and adaptations that I used to activate Audi Active Lane Assist, I am not making any promises or assuming responsibility, code at your own risk, But it worked perfectly for me. I do get a few faults but I think it is due to me trying to activate Traffic Sign Recognition. UPDATE: Unchecking the option for STA in A5 coding (Byte 16->Bit 5) and you will no longer get the congestion assist fault code. You will get a few bings from your car about Pre Sense Malfunction, these will all go away once you are done. This will activate the self steering, steering wheel vibration, and lane crossing warning. Do all the coding then do adaptations. If using OBDEleven use all the directions only on the left half of the "|" symbol, if using VCDS use all the directions on the right side of the "|". UPDATE: Security codes: A5- 20103 ALL Coding: A5 - Frt Sens. Drv. Assist HC>Active | Byte 16>Bit 7 EFP>Active | Byte 12>Bit 3 17 - Dash Board (One of these may already be on, make sure both are) Lane Assistant>Active | Byte 4>Bit 6 Lane Change Assistant>Active | Byte 5>Bit 3 09 - Central Electrics Heading Control Config>heading_control | Byte 35>Bit 0 44 - Steering Assistance Heading Control Assistant>Active | Byte 2>Bit 7 ALL ADAPTATIONS: 5F - Information Electronics Car_Function_Adaptations_Gen2>menu_display_Lane_Departure_Warning = Set Value to “Activated” Car_Function_Adaptations_Gen2>menu_display_Lane_Departure_Warning_over_threshold_high = Set Value to “Activated” Car_Function_List_BAP_Gen2>LDW_HCA_0x19> Set Value to “Activated” Car_Function_List_BAP_Gen2-LDW_HCA_0x19_msg_bus> Set Value to “Terminal 15” A5 - Frt Sens. Drv. Assist BAP Personalization = Set Value to “Not Activated” Personalization of lane dept. warning Cl. 15 on = Set value to “Last Setting” System mode, lane depart. warn, = Set Value to “Selection via menu” Switch-on condition, lane depart. warn. = Set value to “On” (I had to toggle this as this is the final step that I believe mimics pressing the button to actually activate it. You know it was successful when the Lane markings show up in the VC) You can tweak the vibration intensity, warning time, and steering effort in these A5 adaptations: UPDATE Directional stabilization assist driver inact deactiv threshold (3 options) Directional stab. assist.: intensity: steering wheel vibration (3 options) Directional stab. assist.: intensity: power steering support (3 options) www.audiworld.com/forums/a4-b9-platform-discussion-212/coding-turning-audi-active-lane-assist-all-cars-pre-sense-2907906/ |
|
|
|
Post by Mj on Dec 11, 2016 10:14:58 GMT
Great info, thanks!
Are you able to enable/disable it from the MMI once configured, or do you need change the coding again?
|
|
nike
New Member
Posts: 2 
|
Post by nike on Dec 13, 2016 18:45:08 GMT
you cannot disable. only able change from early to late
you have to code again to fully disable
|
|
|
|
Post by trocoli on Mar 17, 2017 16:17:32 GMT
I have problem
Codigos de error:
U112100 - Falta el mensaje del bus de datos
Estática
Datos ambientales dinámicos: 028D4F02857F
Date: 2017-03-16 18:52:59
Contador de la frecuencia con que se producen las averías: 1
Mileage: 47298 km
Borrador de averías sin confirmar: 97
Prioridad: 6
|
|
|
|
Post by Ry13 on May 29, 2017 15:46:03 GMT
Hi, has anyone successfully done this for a b9 with pre sense?
|
|
|
|
Post by Tech0515 on Aug 12, 2017 21:43:41 GMT
Hi, has anyone successfully done this for a b9 with pre sense? Yes. It works |
|
|
|
Post by dany81 on Aug 30, 2017 15:07:01 GMT
Hi, has anyone successfully done this for a b9 with pre sense? Yes. It works Do you mean pre sense city? The One included in all models (not optional)? |
|
Deleted
Deleted Member
Posts: 0
|
Post by Deleted on Aug 30, 2017 15:40:54 GMT
I have problem Codigos de error: U112100 - Falta el mensaje del bus de datos Estática Datos ambientales dinámicos: 028D4F02857F Date: 2017-03-16 18:52:59 Contador de la frecuencia con que se producen las averías: 1 Mileage: 47298 km Borrador de averías sin confirmar: 97 Prioridad: 6 trocoll check out obdeleven.proboards.com/thread/1783/fix-error-codes there are some details of error codes that i have seen and fixed. Specifically the U112100 When this was raised with don (VWVortex Thread) he gave some simple advise "Very difficult to diagnose a general fault code like the one in your post from just the brief information provided. I suggest that you go to the history file for the control module to find out what changes you made and then revert back the setting to their original values." so I followed this simple advise and now I don't have an error. What I generally find is this error comes when you have turned something on that the hardware you have installed does not support the change, so for example today I turned on Blind Spot detection but dont have the sensors so get this error. Hope that helps. |
|
|
|
Post by indu on Oct 21, 2017 23:28:19 GMT
There are no values on my car for
A5 - Frt Sens. Drv. Assist
BAP Personalization = Set Value to “Not Activated”
Personalization of lane dept. warning Cl. 15 on = Set value to “Last Setting”
System mode, lane depart. warn, = Set Value to “Selection via menu”
Switch-on condition, lane depart. warn. = Set value to “On” (I had to toggle this as this is the final step that I believe mimics pressing the button to actually activate it. You know it was successful when the Lane markings show up in the VC)
You can tweak the vibration intensity, warning time, and steering effort in these A5 adaptations:
UPDATE
Directional stabilization assist driver inact deactiv threshold (3 options)
Directional stab. assist.: intensity: steering wheel vibration (3 options)
Directional stab. assist.: intensity: power steering support (3 options)
|
|
|
|
Post by mikes on Dec 27, 2017 14:47:18 GMT
Does it works Active Lane assist activation ( via APP) on Audi A4 MY 2018?
|
|
jp199
New Member
Posts: 1
|
Post by jp199 on Jun 5, 2018 14:43:23 GMT
Hello , works on new A5, or need to change something ?
BRegards
|
|
|
|
Post by frateken on Jul 17, 2018 6:17:04 GMT
Goooood morning,
I've just activated ALA on my audi a4 avant quattro 2017. It works fine.
Thank you obdeleven
I am looking forward to read a new app on obdeleven, for example:
Fold mirror when I insert the reverse gear
|
|
|
|
Post by Thirsty on Jul 17, 2018 6:31:30 GMT
Goooood morning, I've just activated ALA on my audi a4 avant quattro 2017. It works fine. Thank you obdeleven I am looking forward to read a new app on obdeleven, for example: Fold mirror when I insert the reverse gear Do you mean Passenger mirror lowering when reversing? If yes click here. |
|
|
|
Post by stoofi on Aug 7, 2018 16:16:04 GMT
Hi! I have the Audi A4 B9 with pre sense city installed. When I use the Active Lane Assist APP in OBDELEVEN (app 1 and app 2) I get two faults on the dash: an Active Lane Assist malfuncution and a Pre Sense malfunction. I have tried clearing All faults through OBDELEVEN, but the faults reappear in dash and Lane Assist does not work. 😑😑😑 Would appreciate any suggestions om how to solve. Thanks from Denmark
|
|
|
|
Post by fanfan26 on Aug 7, 2018 21:52:14 GMT
Hi! I have the Audi A4 B9 with pre sense city installed. When I use the Active Lane Assist APP in OBDELEVEN (app 1 and app 2) I get two faults on the dash: an Active Lane Assist malfuncution and a Pre Sense malfunction. I have tried clearing All faults through OBDELEVEN, but the faults reappear in dash and Lane Assist does not work. 😑😑😑 Would appreciate any suggestions om how to solve. Thanks from Denmark did you try to install all 3 apps, cause you have a thrift one , maybe that will clear the faults |
|
|
|
Post by 911carrera on Nov 24, 2018 16:28:57 GMT
A have the same problem when a try to activate the lane assist with the app . I installed the 2 app’s and then I get Lane assist malfunction and pre sense malfunction .
Is there a 3the app for activating lane assist ?
|
|
vax77
New Member
Posts: 4
|
Post by vax77 on Nov 25, 2018 16:31:27 GMT
A have the same problem when a try to activate the lane assist with the app . I installed the 2 app’s and then I get Lane assist malfunction and pre sense malfunction . Is there a 3the app for activating lane assist ? even my two cars have the same problem |
|
vax77
New Member
Posts: 4
|
Post by vax77 on Nov 26, 2018 23:01:42 GMT
A have the same problem when a try to activate the lane assist with the app . I installed the 2 app’s and then I get Lane assist malfunction and pre sense malfunction . Is there a 3the app for activating lane assist ? does anyone have the fix for this problem? |
|
vax77
New Member
Posts: 4
|
Post by vax77 on Dec 16, 2018 22:21:36 GMT
Anyone???
|
|
|
|
Post by andy18 on Jan 2, 2019 9:18:40 GMT
Active lane assist works with new app. I have activated on my A4 B9 2016 Model. Just followed the steps.
After activation of step 1, i got error of pre-sense malfunction but after step 2 it was gone.
Everything works fine.
|
|
|
|
Post by 911carrera on Jan 26, 2019 23:26:21 GMT
Is there a New app for the lane assist ?
How do you now ?
Last time a use the fitst app and than the second,but the errors didn’t go away .
That cost me 200 credits 100 to activate and 100 to deactivate again.
Did anyone retry to activate the lane assist ?
|
|
vax77
New Member
Posts: 4
|
Post by vax77 on Feb 17, 2019 19:07:36 GMT
All work ok for my audi 2016
|
|
|
|
Post by avaneylen on Jun 15, 2019 8:32:03 GMT
Owning a A4 B9 2019 and having the same problem as stoofi and 911carrera, i'm also getting these two errors when trying to code it. I've tried both ways, through the 'apps' from obdEleven and via the longocing provided in this thread.
Hopefully someone comes with a solution for this.  |
|
|
|
Post by jryacr on Aug 14, 2019 4:32:37 GMT
not my coding but i did think it would be nice to share link to original post below Here is the coding and adaptations that I used to activate Audi Active Lane Assist, I am not making any promises or assuming responsibility, code at your own risk, But it worked perfectly for me. I do get a few faults but I think it is due to me trying to activate Traffic Sign Recognition. UPDATE: Unchecking the option for STA in A5 coding (Byte 16->Bit 5) and you will no longer get the congestion assist fault code. You will get a few bings from your car about Pre Sense Malfunction, these will all go away once you are done. This will activate the self steering, steering wheel vibration, and lane crossing warning. Do all the coding then do adaptations. If using OBDEleven use all the directions only on the left half of the "|" symbol, if using VCDS use all the directions on the right side of the "|". UPDATE: Security codes: A5- 20103 ALL Coding: A5 - Frt Sens. Drv. Assist HC>Active | Byte 16>Bit 7 EFP>Active | Byte 12>Bit 3 17 - Dash Board (One of these may already be on, make sure both are) Lane Assistant>Active | Byte 4>Bit 6 Lane Change Assistant>Active | Byte 5>Bit 3 09 - Central Electrics Heading Control Config>heading_control | Byte 35>Bit 0 44 - Steering Assistance Heading Control Assistant>Active | Byte 2>Bit 7 ALL ADAPTATIONS: 5F - Information Electronics Car_Function_Adaptations_Gen2>menu_display_Lane_Departure_Warning = Set Value to “Activated” Car_Function_Adaptations_Gen2>menu_display_Lane_Departure_Warning_over_threshold_high = Set Value to “Activated” Car_Function_List_BAP_Gen2>LDW_HCA_0x19> Set Value to “Activated” Car_Function_List_BAP_Gen2-LDW_HCA_0x19_msg_bus> Set Value to “Terminal 15” A5 - Frt Sens. Drv. Assist BAP Personalization = Set Value to “Not Activated” Personalization of lane dept. warning Cl. 15 on = Set value to “Last Setting” System mode, lane depart. warn, = Set Value to “Selection via menu” Switch-on condition, lane depart. warn. = Set value to “On” (I had to toggle this as this is the final step that I believe mimics pressing the button to actually activate it. You know it was successful when the Lane markings show up in the VC) You can tweak the vibration intensity, warning time, and steering effort in these A5 adaptations: UPDATE Directional stabilization assist driver inact deactiv threshold (3 options) Directional stab. assist.: intensity: steering wheel vibration (3 options) Directional stab. assist.: intensity: power steering support (3 options) www.audiworld.com/forums/a4-b9-platform-discussion-212/coding-turning-audi-active-lane-assist-all-cars-pre-sense-2907906/ |
|
|
|
Post by jryacr on Aug 14, 2019 4:34:30 GMT
Sorry for the stupid question but im new to this forum...i currently owned 2019 S4 but didnt come with lane assist. Does this mean I can add lane assist using this code?
|
|
lethi
New Member
Posts: 2
|
Post by lethi on Sept 6, 2019 14:23:52 GMT
Do you mean pre sense city? The One included in all models (not optional)? did you ever found out if it does work with the standard one? |
|
|
|
Post by nikolapervan on Nov 13, 2019 11:49:59 GMT
|
|
|
|
Post by briannyg on Nov 23, 2019 14:20:49 GMT
|
|
|
|
Post by briannyg on Nov 25, 2019 17:21:10 GMT
update, the auto highbeams do work. figured out you just need to always activate them at night. they dont go on automatically.. is this same for others ?
|
|
|
|
Post by rollehjort on Jul 28, 2020 9:37:43 GMT
Hi
I have the same problem with my 2017 A4. I have first tried to activate Lane Assist through the 2 step in Apps and then getting faults for Lane assist and pre sence.
Then I tried to undo the settings in apps but getting faults when trying.
After that I tried manual coding and still got the same faults.
Then i tried to inaktivate the settings trough the 2 steps Apps and I am now back to default settings.
I have lost my points by using the Apps but I have no faults and not Active Line Assist.
When I tried to do this I hade the bonnet open and I’ve reset the mmi after programming.
I noticed that the EFP was not active after doing the apps coding and I couldn’t activate it first but when did it by longcoding it changed.
Next step would be to try doing it manual again and see I will work.
|
|
but I have managed to activate auto high-beams, and hoped since that worked, the Lane Assist will work too but unfortunately it gives me errors so I needed to revert back. I lost 300 points in the process, but OBD11 support restored them back - I'm thankful.
